Cisco Catalyst Cellular Gateways Command Reference Guide
First Published: 2023-03-07
Last Modified: 2023-04-17
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
©
2023 Cisco Systems, Inc. All rights reserved.
CONTENTS
Show Commands 1
CHAPTER 1
show cellular 1 connections 2
show cellular 1 hardware 3
show cellular 1 profile 4
show cellular 1 radio 5
show cellular 1 radio-band 6
show cellular 1 radio-details 8
show cellular 1 modem-logging 9
show cellular 1 qos 10
show cellular 1 details 13
show cellular 1 firmware 14
show cellular 1 network 15
show cellular 1 sim 16
Configuration Commands 17
CHAPTER 2
gw-action:request admin-tech 18
gw-action:request file list 19
gw-action:request ping 20
gw-action:request software 21
Cisco Catalyst Cellular Gateways Command Reference Guide
iii
Cisco Catalyst Cellular Gateways Command Reference Guide
iv
Contents
Show Commands
• show cellular 1 connections, on page 2
• show cellular 1 hardware, on page 3
• show cellular 1 profile, on page 4
• show cellular 1 radio, on page 5
• show cellular 1 radio-band, on page 6
• show cellular 1 radio-details, on page 8
• show cellular 1 modem-logging, on page 9
• show cellular 1 qos, on page 10
• show cellular 1 details, on page 13
• show cellular 1 firmware, on page 14
• show cellular 1 network, on page 15
• show cellular 1 sim, on page 16
Cisco Catalyst Cellular Gateways Command Reference Guide
1
show cellular 1 connections
To display the sessions information, use the show cellular 1 connections command in user EXEC mode.
show cellular 1 connections
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 connections command to display the sessions information.
Example
This example shows how to view the sessions information
Router# show cellular 1 connections
Profile ID = 1
---------------------------
APN = broadband
Connectivity = Attach and Data
Session Status = Connected
IPv4 Address = 10.20.20.60
IPv4 Gateway Address = 10.19.19.60
IPv4 Primary DNS = 10.0.0.8
IPv4 Secondary DNS = 10.0.0.4
IPv6 Address = 2001:db8:ffff:ffff:ffff:fffe:ffff:ffff, IPv6 Prefix length = 64
IPv6 Gateway Address = 2001:db8:ffff:ffff:fffe:fffe:fffe:fffe, IPv6 Gateway Prefix length
= 64
IPv6 Primary DNS = 2001:db8:1000::2000
IPv6 Secondary DNS = 2001:db8:1111::2222
Tx Packets = 1009655, Rx Packets = 983984
Tx Bytes = 297251993, Rx Bytes = 211848740
Tx Drops = 0, Rx Drops = 0
Tx Overflow Count = 0, Rx Overflow Count = 0
Cisco Catalyst Cellular Gateways Command Reference Guide
2
Show Commands
show cellular 1 connections
show cellular 1 hardware
To display the cellular unit hardware information, use the show cellular 1 hardware command in user EXEC
mode.
show cellular 1 hardware
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 hardware command to display the cellular unit hardware information.
This example shows how to view all the cellular unit hardware information:
Router# show cellular 1 hardware
Modem Firmware Version = SWIX55C_01.07.19.00 000000 jenkins
Device Model ID = EM9190
International Mobile Subscriber Identity (IMSI) = 123456700002084
International Mobile Equipment Identity (IMEI) = 351735110112295
Integrated Circuit Card ID (ICCID) = 8952530076180182084
Mobile Subscriber Integrated Services Digital Network Number (MSISDN) =
Factory Serial Number (FSN) = 4H0335005303A1
Current Modem Temperature = 44 deg C
PRI SKU ID = 1104567
PRI Version = 016.010_000
Carrier = GENERIC
OEM PRI Version = 001.020
Modem Status = MODEM_STATE_DNS_ACQUIRED
Cisco Catalyst Cellular Gateways Command Reference Guide
3
Show Commands
show cellular 1 hardware
show cellular 1 profile
To display the cellular profile details, use the show cellular 1 profile command in user EXEC mode.
show cellular 1 profile
Syntax Description
This command has no arguments or keywords.
Command Default
No default behavior or values.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 profile command to display cellular profile details.
This example shows how to view all the cellular unit profile information:
Router# show cellular 1 profile
PROFILE ID APN PDP TYPE STATE AUTHENTICATION USERNAME PASSWORD
-------------------------------------------------------------------------------
1 broadband IPv4v6 ACTIVE none - -
Cisco Catalyst Cellular Gateways Command Reference Guide
4
Show Commands
show cellular 1 profile
show cellular 1 radio
To display the cellular modem radio information, use the show cellular 1 radio command in user EXEC
mode.
show cellular 1 radio
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 radio command display the cellular modem radio information.
Example
This example shows how to view the cellular modem radio information
Router# show cellular 1 radio
Radio Power Mode = online
Radio Access Technology(RAT) Selected = LTE
LTE Rx Channel Number(PCC) = 0
LTE Tx Channel Number(PCC) = 0
LTE Band = 1
LTE Bandwidth = 20 MHz
Current RSSI = -25 dBm
Current RSRP = -52 dBm
Current RSRQ = -7 dB
Current SNR = 30.0 dB
Physical Cell Id = 1
Network Change Event = activated LTE
CellularGateway#
Cisco Catalyst Cellular Gateways Command Reference Guide
5
Show Commands
show cellular 1 radio
show cellular 1 radio-band
To display the radio band settings, use the show cellular 1 radio-band command in user EXEC mode.
show cellular 1 radio-band
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 radio-bandcommand to display the radio band settings.
Example
This example shows how to display the radio band settings.
Router# show cellular 1 radio-band
LTE bands supported by modem:
1 2 3 4 5 7 8 12 13 14 17 18 19 20 25 26 28 29 30 32 34 38 39 40 41 42 46 48 66 71
LTE band Preference settings for the active sim:
1 2 3 4 5 7 8 12 13 14 17 18 19 20 25 26 28 29 30 32 34 38 39 40 41 42 46 48 66 71
NR5G bands supported by modem:
1 2 3 5 28 41 66 71 77 78 79
NR5G band Preference settings for the active sim:
1 2 3 5 28 41 66 71 77 78 79
Non-LTE bands supported by modem:
23 - WCDMA (Europe, Japan, and China) 2100 band
24 - WCDMA US PCS 1900 band
25 - WCDMA (Europe and China) DCS 1800 band
26 - WCDMA US 1700 band
27 - WCDMA US 850 band
28 - WCDMA Japan 800 band
50 - WCDMA Europe and Japan 900 band
51 - WCDMA Japan 1700 band
61 - WCDMA Japan 850 band
Non-LTE band Preference settings for the active sim:
23 - WCDMA (Europe, Japan, and China) 2100 band
24 - WCDMA US PCS 1900 band
25 - WCDMA (Europe and China) DCS 1800 band
26 - WCDMA US 1700 band
27 - WCDMA US 850 band
28 - WCDMA Japan 800 band
50 - WCDMA Europe and Japan 900 band
51 - WCDMA Japan 1700 band
Cisco Catalyst Cellular Gateways Command Reference Guide
6
Show Commands
show cellular 1 radio-band
61 - WCDMA Japan 850 band
============================================
Band index reference list:
For LTE indices 1-128 correspond to bands 1-128 and NR indeces 1-320 correspond to bands
1-320.
For 3G, indices 1-64 maps to the 3G bands mentioned against each above.
Cisco Catalyst Cellular Gateways Command Reference Guide
7
Show Commands
show cellular 1 radio-band
show cellular 1 radio-details
To display the cellular information when the radio goes to Low Power mode, use the show cellular 1
radio-details command in user EXEC mode.
show cellular 1 radio-details
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 radio-details command to display the carrier aggregation and other radio details.
Example
This example shows how to view the carrier aggregation and additional radio details.
Router# show cellular 1 radio-details
Carrier Aggregation Status = Disabled
LTE RX Channel Number(PCC) = 0
LTE TX Channel Number(PCC) = 0
LTE Band = 4
LTE Bandwidth = 20 MHz
PCC CA information:
-------------------
LTE band class = 4
E-UTRA absolute radio frequency channel number of the serving cell = 0
Bandwidth = 20 MHz
Physical Cell Id = 28
Current RSRP in 1/10 dBm as measured by L1 = -99 dBm
Current RSSI in 1/10 dBm as measured by L1 = -73 dBm
Current RSRQ in 1/10 dBm as measured by L1 = -7 dB
Measured SINR in dB = 25.2 dB
Tracking area code information for LTE = 1
5G CC information:
------------------
Current ENDC RSRP in 1/10 dBm as measured by L1 = 0 dBm
Current ENDC RSRQ in 1/10 dBm as measured by L1 = 0 dB
Measured ENDC SINR in dB = 0.0 dB
Cisco Catalyst Cellular Gateways Command Reference Guide
8
Show Commands
show cellular 1 radio-details
show cellular 1 modem-logging
To display the cellular modem logging information, use the show cellular 1 modem-logging command in
user EXEC mode.
show cellular 1 modem-logging
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first integrated in this release.Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 modem-logging command to obtain information like DMlogs, NAS logs, SDK logs,
and driver logs running data.
Examples
This example shows how to view all the cellular unit hardware information:
show cellular 1 modem-logging
modem-logging dm-logs-status not-started
Related Commands
DescriptionCommand
Displays the list of firmwares stored on the modem.show cellular 1 firmware
Cisco Catalyst Cellular Gateways Command Reference Guide
9
Show Commands
show cellular 1 modem-logging
show cellular 1 qos
To display the cellular QoS related information, use the show cellular 1 qos command in user EXEC mode.
show cellular 1 qos
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first introduced in this release.Cisco IOS CG 17.11.x
release
Usage Guidelines
The show cellular 1 qos command displays information about the QoS parameters for each of the QoS flow
set by the network.
Examples
This example shows how to view all the cellular QoS information:
show cellular 1 qos
CG522-E# % qos qosflow-list 0
QoS Id = 1434
QoS State = ENABLED
QoS Flow Type = NETWORK_INITIATED
Bearer Id = 50
Tx flow info:
Lte Qci = 5
Data Rate Max = 0
Minimum Data Rate Guaranteed = 0
Rx flow info:
Lte Qci = 5
Data Rate Max = 0
Minimum Data Rate Guaranteed = 0
Tx filter info:
IP version = IPV4
IPv4 Source Address = 209.165.200.225
IPv4 Source Address subnet mask = 255.255.255.224
IPv4 Dest Address = 209.165.200.230
IPv4 Dest Address subnet mask = 255.255.255.0
Tos value = 128
Tos mask = 192
IPv6 Source Address = ::
Source IPv6 address prefix length = 0
IPv6 Dest Address = ::
Dest IPv6 address prefix length = 0
IPv6 Label = 0
Transport Protocol = 0
Transport Port1 = 0
Transport Range1 = 0
Transport Port2 = 0
Cisco Catalyst Cellular Gateways Command Reference Guide
10
Show Commands
show cellular 1 qos
Transport Range2 = 0
Transport Port3 = 0
Transport Range3 = 0
Transport Port4 = 0
Transport Range4 = 0
Rx filter info:
IP version = IPV4
IPv4 Source Address = 209.165.201.1
IPv4 Source Address subnet mask = 255.255.255.224
IPv4 Dest Address = 209.165.201.10
IPv4 Dest Address subnet mask = 255.255.255.224
Tos value = 128
Tos mask = 192
IPv6 Source Address = ::
Source IPv6 address prefix length = 0
IPv6 Dest Address = ::
Dest IPv6 address prefix length = 0
IPv6 Label = 0
Transport Protocol = 0
Transport Port1 = 0
Transport Range1 = 0
Transport Port2 = 0
Transport Range2 = 0
Transport Port3 = 0
Transport Range3 = 0
Transport Port4 = 0
Transport Range4 = 0
qos qosflow-list 1
QoS Id = 1435
QoS State = ENABLED
QoS Flow Type = NETWORK_INITIATED
Bearer Id = 51
Tx flow info:
Lte Qci = 4
Data Rate Max = 7000
Minimum Data Rate Guaranteed = 5000
Rx flow info:
Lte Qci = 4
Data Rate Max = 7000
Minimum Data Rate Guaranteed = 5000
Tx filter info:
IP version = IPV4
IPv4 Source Address = 209.165.202.129
IPv4 Source Address subnet mask = 255.255.255.224
IPv4 Dest Address = 209.165.202.158
IPv4 Dest Address subnet mask = 255.255.225.224
Tos value = 0
Tos mask = 0
IPv6 Source Address = ::
Source IPv6 address prefix length = 0
IPv6 Dest Address = ::
Dest IPv6 address prefix length = 0
IPv6 Label = 0
Transport Protocol = 0
Transport Port1 = 0
Transport Range1 = 0
Transport Port2 = 0
Transport Range2 = 0
Transport Port3 = 0
Transport Range3 = 0
Cisco Catalyst Cellular Gateways Command Reference Guide
11
Show Commands
show cellular 1 qos
Transport Port4 = 0
Transport Range4 = 0
Rx filter info:
IP version = IPV4
IPv4 Source Address = 209.165.202.139
IPv4 Source Address subnet mask = 255.255.225.0
IPv4 Dest Address = 209.165.202.149
IPv4 Dest Address subnet mask = 255.255.255.0
Tos value = 0
Tos mask = 0
IPv6 Source Address = ::
Source IPv6 address prefix length = 0
IPv6 Dest Address = ::
Dest IPv6 address prefix length = 0
IPv6 Label = 0
Transport Protocol = 0
Transport Port1 = 0
Transport Range1 = 0
Transport Port2 = 0
Transport Range2 = 0
Transport Port3 = 0
Transport Range3 = 0
Transport Port4 = 0
Transport Range4 = 0
qos qosflow-list 2
QoS Id = 1436
QoS State = ENABLED
QoS Flow Type = NETWORK_INITIATED
Bearer Id = 0
Tx flow info:
Lte Qci = 6
Data Rate Max = 0
Minimum Data Rate Guaranteed = 0
Rx flow info:
Lte Qci = 6
Data Rate Max = 0
Minimum Data Rate Guaranteed = 0
Transport Range4 = 0
Related Commands
DescriptionCommand
Displays the cellular profile details.show cellular 1 profile
Cisco Catalyst Cellular Gateways Command Reference Guide
12
Show Commands
show cellular 1 qos
show cellular 1 details
To display the detailed cellular information, use the show cellular 1 details command in user EXEC mode.
show cellular 1 details
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 details command to display the detailed cellular information.
This example shows how to view the detailed cellular information:
Router# show cellular 1 details
Cellular Interface status = Up
Cellular Modem Status = Network-Ready
Cellular IP Address = 10.10.0.1
Cellular Default Gateway = 10.10.0.2
Cellular Subnet Mask = 255.0.0.0
Cellular Primary DNS Address = 10.10.0.3
Cellular Secondary DNS Address = 10.10.0.4
Cellular IPv6 Address = 2001:db8:ffff:ffff:ffff:fffe:ffff:ffff
Cellular IPv6 Default Gateway = 2001:db8:ffff:ffff:fffe:fffe:fffe:fffe
Cellular IPv6 Primary DNS Address = 2001:db8:1000::2000
Cellular IPv6 Secondary DNS Address = 2001:db8:1111::2222
Cisco Catalyst Cellular Gateways Command Reference Guide
13
Show Commands
show cellular 1 details
show cellular 1 firmware
To display the list of firmwares stored in the modem, use the show cellular 1 firmware command in user
EXEC mode.
show cellular 1 firmware
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 firmware command to display the list of firmwares stored in the modem.
This example shows how to view the list of firmwares stored in the modem:
Router# show cellular 1 firmware
Firmware Activation Mode = AUTO
INDEX CARRIER FW VERSION PRI VERSION STATUS
--------------------------------------------------------
1 GENERIC 01.07.19.00_GEN 016.010_000 ACTIVE
2 GENERIC2 01.07.19.00_GEN2 012.012_000 INACTIVE
Cisco Catalyst Cellular Gateways Command Reference Guide
14
Show Commands
show cellular 1 firmware
show cellular 1 network
To display the cellular network information, use the show cellular 1 network command in user EXEC mode.
show cellular 1 network
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 network command to display the cellular network information.
This example shows how to view the cellular network information:
CellularGateway# show cellular 1 network
Current System Time = Fri Jan 21 22:54:17 2023
Current Service Status = Normal
Current Service = Packet switched
Current Roaming Status = Home
Network Selection Mode = Automatic
Network = 123 456
Mobile Country Code (MCC) = 123
Mobile Network Code (MNC) = 456
Packet Switch domain(PS) state = Attached
EMM State = Registered
EMM Sub state = Normal-Service
RRC Connection State = RRC Connected
Tracking Area Code (TAC) = 1
Cell ID = 7169
Network MTU = 1500
Cisco Catalyst Cellular Gateways Command Reference Guide
15
Show Commands
show cellular 1 network
show cellular 1 sim
To display the cellular modem SIM information, use the show cellular 1 sim command in user EXEC mode.
show cellular 1 sim
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was
introduced.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the show cellular 1 sim command to display the cellular modem SIM information.
This example shows how to view the cellular modem SIM information:
Router# show cellular 1 sim
Cellular Dual SIM details:
SIM 0 = Present
SIM 1 = Not Present
Active SIM = 0
Cisco Catalyst Cellular Gateways Command Reference Guide
16
Show Commands
show cellular 1 sim
Configuration Commands
• gw-action:request admin-tech, on page 18
• gw-action:request file list, on page 19
• gw-action:request ping, on page 20
• gw-action:request software, on page 21
Cisco Catalyst Cellular Gateways Command Reference Guide
17
gw-action:request admin-tech
To create admin tech logs file which is required for customer support, use the gw-action:request admin-tech
command in user EXEC mode.
gw-action : request admin-tech
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first integrated into the Cisco IOS XE 17.3.x
release.
Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Use the gw-action:request admin-tech command to create admin tech logs file that is used for troubleshooting
purposes for customer support.
Examples
CG522-E# gw-action:request admin-tech
Log
Creating support bundle, please wait...
Support file CG522-E.support.user.20230120.114157.tgz created in /flash
Cisco Catalyst Cellular Gateways Command Reference Guide
18
Configuration Commands
gw-action:request admin-tech
gw-action:request file list
To display the files listed on the specified location, use the gw-action:request file list command in the user
EXEC mode.
gw-action: request file list
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first integrated into this release.Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Examples
This example shows how to view all the file related actions that you can perform:
gw-action:request file list
-rw-r--r-- 59906252 Sep 22 18:44 CG522-E.support.20220922.184252.tgz
-rw-r--r-- 199807 Jan 20 11:42 CG522-E.support.user.20230120.114157.tgz
drwxrwxrwx 4096 Jan 17 21:02 DL-SW-IMAGES
-rw-r--r-- 1761 Nov 5 15:55 cacert.pem
d--------- 4096 Aug 21 2021 fw_upgrade_sysinfo
-rw-r--r-- 0 Mar 18 2022 issue.pcap
drwx------ 16384 Oct 1 2021 lost+found
-rw-r--r-- 1761 Oct 1 2021 old_cacert.pem
drwxr-xr-x 4096 Jan 20 11:41 storage
-rw-r--r-- 175 Jan 20 11:39 sw_script_upg_confirm.log
-rw-r--r-- 7626 Jan 17 21:03 sw_script_upgrade_task.log
drwxr-xr-x 4096 Oct 1 2021 tmp
Cisco Catalyst Cellular Gateways Command Reference Guide
19
Configuration Commands
gw-action:request file list
gw-action:request ping
To display the IPv4 and IPv6 ping information, use the gw-action:request ping command in user EXEC
mode.
gw-action: request ping
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first integrated into this release.Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Examples
This example shows the ping information for the IPv4 and IPv6 addresses:
gw-action:request ping 192.0.2.12
Success :192.0.2.12 (192.0.2.12): 56 data bytes
192.0.2.12 ping statistics
5 packets transmitted, 5 packets received, 0% packet loss round
trip min/avg/max = 43.438/51.709/56.303 ms
gw-action:request ping 2001:DB8::1
Success :2001:DB8::1 (2001:DB8::1): 56 data bytes
2001:DB8::1 ping statistics
5 packets transmitted, 5 packets received, 0% packet loss round
trip min/avg/max = 32.468/40.010/49.135 ms
Cisco Catalyst Cellular Gateways Command Reference Guide
20
Configuration Commands
gw-action:request ping
gw-action:request software
To display all the software related information, use the gw-action:request software command in user EXEC
mode.
gw-action: request software
Syntax Description
This command has no arguments or keywords.
Command Default
This command has no default settings.
Command Modes
User EXEC
Command History
ModificationRelease
This command was first integrated into this release.Cisco IOS XE Amsterdam 17.3.x release
Usage Guidelines
Examples
This example shows all the software image related operations:
gw-action:request software
Possible completions:
activate Activate software image
download Download software image or other file to the device
install Install software image
upgrade Download, Install and Activate software
Cisco Catalyst Cellular Gateways Command Reference Guide
21
Configuration Commands
gw-action:request software
Cisco Catalyst Cellular Gateways Command Reference Guide
22
Configuration Commands
gw-action:request software